Shiro Cordless Telephone SD8301 User Manual

User Manual •  
SD8301  
Digital Enhanced Cordless Communication  
 
User Manual  
WHAT THE SYMBOLS MEAN  
Battery charge level  
Whenever this shows ‘nearly empty’ ( ), put the handset on the base unit to charge the  
batteries. While the battery is being charged, the level shown will keep changing.  
Mute  
Your handset's microphone is muted.  
Signal level  
Shows the strength of the signal between the handset and base unit, and flashes when you  
are out of range of the base unit, when the level is low, or the symbol is flashing, move  
closer to base unit.  
Phone  
To indicate there is a missed call.  
Speakerphone  
Your handset’s loudspeaker is on.  
Messages  
Message has been received.  
Lock  
Your handset’s keypad is locked.  
2
 
User Manual  
KEYPAD DESCRIPTION (HANDSET + BASE UNIT)  
Left Key  
Right Key Button  
Press to enter menu and sub-  
menu mode;  
Press to confirm selection;  
With the key “ * ” to lock or  
unlock the keypad;  
In standby mode, press to enter  
phonebook menu;  
Press during programming to go  
back to the previous option, or  
to clear digits from the display.  
Press during a call to mute the  
mouthpiece  
Up and Down Button  
INT button  
Press during programming to  
move through the menu.  
Press during a call to change  
the volume in the earpiece.  
Press to make an intercom  
call (if you have more  
than one handset)  
Speakerphone Button  
Press to turn the  
speakerphone ON/OFF  
CALL button  
Press to begin, answer and  
end a telephone call.  
PAUSE Button  
Press to insert PAUSE  
while dialing out  
Register Recall button  
P
You need the Recall  
function if your phone is  
connected to a PABX, or if  
CHARGE  
The CHARGE light comes on  
when the handset's  
PAGE  
you use select services;  
When you make an  
outside call, press to  
transfer it to another  
handset.  
batteries are being charged.  
HANDSET LOCATOR  
Press this to make the handset  
ring, if you cannot remember  
where you put it.  
SMS Button  
IN USE light  
Press it again to stop the  
handset ringing.  
Press this to go SMS  
mode directly while the  
handset is in idle mode.  
The IN USE light comes  
on when you have a  
connection to the  
telephone line.  
Before you can use the handset to  
make calls for the first time, you  
will need to fit and fully charge the  
battery for 15 hours.  
3
 
User Manual  
SETTING UP YOUR TELEPHONE  
Connection and conditions for use  
You can connect your phone to a direct exchange line (DEL), a line connected to a local  
exchange, with its own phone number; to an extension socket connected to a DEL; or to an  
extension on an approved compatible PBX. Do not connect the Phone as an extension to a  
payphone.  
How many phones can you connect?  
The ringer equivalence numbers (RENs) of all instruments (phones, fax machines, etc.)  
connected to an exchange line must not add up to more than 4, otherwise, one or more of  
them may not ring and/or answer calls correctly. The Phone has a REN of 1, and most other  
telephones have a REN of 1 unless marked otherwise.  
Radio signals between handset and base unit  
To use your handset and base unit together, you must be able to establish a radio link  
between them. Be aware that:  
Sitting the base unit as high as possible will give better results, in a two-storey  
house, the best position may be on the first-floor landing.  
Any large metal object, like a fridge, a mirror or a filing cabinet, between the  
handset and base unit may block the radio signal.  
Other solid structures, like walls, may reduce the signal strength.  
Choosing a site for the base unit  
The base unit should be placed on a level surface, in a position where:  
The adapter plug will reach a 230 V AC switched mains supply socket; never try to  
lengthen the mains power cable.  
The telephone cable will reach your telephone line socket or extension socket.  
It is not close to another telephone, this can cause radio interference.  
It is not close to a sink, bath or shower, or anywhere else where it might get wet.  
It is not close to other electrical equipment, fridges, washing machines, microwave  
ovens, TVs, fluorescent lights, etc.  
What's in this pack  
Please check the box contents for completeness.  
If any parts are missing, return complete box to your  
supplier.  
The cordless handset  
The base unit  
Rechargeable battery cell(AAA size x 2 PCS)  
A telephone line cable (different from country to  
country)  
A mains power lead and adaptor (different from  
country to country)  
Charger pods (not available for single handset)  
User manual  
Note: Keep your proof of purchase to support any guarantee  
claim.  
4
 
User Manual  
INSTALLATION  
1. Choose a suitable site for the base unit  
Make sure it is not near to another telephone, nor to other electrical equipment.  
2. Plug the mains power lead and  
the telephone line cord into the  
rear of the base unit.  
3. Plug the mains adapter into a  
230 V AC, 50 Hz mains socket with  
the switch on the socket set to  
OFF.  
Note: The illustration of adaptor may vary  
from country to country.  
4. Switch on mains power at the socket  
5. Fit the battery in the handset(s)  
Insert the battery cell as shown  
Fit the battery compartment cover,  
sliding it until it clicks firmly into  
Position.  
6. Connect the base unit to the telephone line  
Switch off power at the mains socket.  
Insert the telephone line plug into the socket.  
Switch mains power back on  
Make sure the mains socket is  
switched on if you want to use  
the phone---it will not work  
without electrical power.  
Note:  
1. The charger pod does not have a connection to  
the telephone line.  
2. When Handset is placed onto the charge pod, a  
red light lights up to indicate it is charging.  
Use the plug to raise the shutter  
before pushing it into the socket  
3. The illustration of telephone's socket may vary  
from country to country.  
5
 
User Manual  
IMPORTANT SAFETY INFORMATION  
This equipment is not designed for making emergency calls in the event of a power failure.  
Alternative arrangements should be made for access to emergency services.  
(This means that you should also have a basic phone that does not need mains power,  
connected to your line so that you can make calls during a power failure)  
People with a heart pacemaker should consult their doctor before using the telephone.  
If you wear a hearing aid, you should note phone works by transmitting radio waves  
between base and handset that may cause a humming noise.  
1. DO NOT clean any part of your phone with benzene, thinner or other solvent chemicals,  
which may cause permanent damage to your phone. This damage is not covered by the  
Guarantee. When necessary, clean it with a damp cloth.  
Cleaning it with a wet cloth may give you an electric shock.  
2. DO NOT use this equipment in places where volatile or explosive materials may be  
present.  
3. DO NOT let the base unit get wet. Electrical equipment can cause serious injury if used  
while you are wet or standing in water. NEVER use your phone during a thunderstorm.  
Unplug the base unit from the telephone line and the mains socket when there are storms  
in your area. Damage caused by lightning is not covered by the Guarantee.  
4. The phone will produce a certain amount of heat during operation. For this reason it is  
recommended that this equipment is NOT placed in direct contact with antique, veneered  
or delicate furniture surfaces.  
5. DO NOT dispose batteries with normal household waste.  
6. The phone DECT phone emits radio signals which could interfere with other electronic  
equipment, computers, radio, TV set, clock radio alarms, etc.  
A distance of at least one meter should be maintained between phone base station and  
other equipment. This will minimize the risk of such interference.  
7. When you do not need to carry your handsets around, leave them on the base unit or  
charger pod, to keep the batteries charged.  
8. If you hear a warning tone as move around during a call, and/ or the sound in the  
earpiece becomes faint or distorted; you may be going out of range of the base unit.  
Move nearer to the base unit within 20 seconds, until the tone stops. Otherwise your call  
may be cut off.  
WARRANTY INFORMATION  
Your phone is covered by a 12-month warranty from the date of purchase shown on your  
sales receipt. The warranty does not cover the batteries, misuse or damage caused by a  
storm or excessive voltages.  
If you have any problems using the phone, check the Troubleshooting section at the back of  
this manual. If you need to return your phone to our Repair Center while it is under  
guarantee, there will be some handling charge.  
6
 
User Manual  
MAKING AND ANSWERING CALLS  
To switch the handset ON or OFF  
Press and hold the CLEAR button for 2-3 seconds to switch the handset ON or OFF.  
To Make a Call  
1. Key in the telephone number;  
2. Press and hold the CALL button to make a call.  
To Dial a Number from Call Logs  
1. Select <Missed Calls>, <Received Calls> or <Dialed Calls> under CALL INFO mode;  
2. Press left key, the display shows these calls;  
3. Select the telephone number you want to call, then press the CALL button to make  
call  
To Answer a Call  
When the handset and base unit ring, press the CALL button to answer a call.  
When the AUTO TALK is turned on, you can simply answer the call by lifting the  
handset from the base unit (see AUTO TALK).  
To End a Call  
When the talking is over, you just press the CALL button to end the call.  
To Save a Call  
When you scroll through the dialed, received and missed calls numbers, press  
left key, then select <Save>, you can save the call number and name.  
Earpiece Volume  
During a call, you just press UP / DOWN button to adjust the volume of the  
earpiece (1-9 level).  
To Mute the Mouthpiece  
During a call, if you want the person on the other hand end cannot hear you;  
press right key once to mute the mouthpiece;  
While the mouthpiece is muted, you cannot press any number key to send digits  
down the line;  
Press right key again to get back the call To Get Back to the Call.  
MESSAGE FUNCTIONS  
The phone is equipped with text message function, which allows you to send and receive  
SMS (Short Message Service) from other compatible fixed line SMS phones. You need to  
register with your fixed line network operator for the SMS service before using phone for  
messaging. Inbox, Outbox and Draft box can store up to 40 text messages.  
Inbox  
The Inbox is to store the received messages. In order to keep enough space for messages,  
you should delete messages frequently.  
Select <Inbox> under MESSAGE mode, press left key, a list of received messages is  
displayed. Press UP/DOWN button to scroll through the messages;  
The text of message is displayed, then press left key, the display shows the details  
of the message, including the date and the time the message is received;  
After message is read, press left button, you can delete, reply, forward or save  
number.  
7
 
User Manual  
Outbox  
Outbox contains messages you have saved.  
Select <Outbox> under MESSAGE mode, press left key, a list of saved messages is  
displayed. Press UP/DOWN button to scroll through the messages;  
Then you can edit, delete or send the message.  
To Read Message  
Under <MESSAGE> menu, select Inbox, Outbox or Draft, then press left key, you can  
read messages if there’s stored messages.  
To Write Message  
1. Select <Write Message> under MESSAGE mode;  
2. Enter text using the number keypad. Press right key once to clear one letter; press  
and hold right key to clear the screen;  
3. Use the button to backspace;  
4. For symbols, the key “1” is used for the following symbols: ? ! @ $ % ^ &;  
5. Press number “0” twice consecutively, it is used for Spacebar.  
6. If text entry is interrupted by incoming call, the message will be saved in the draft  
box.  
To Send Message  
1. After entering a message, then press left key, you can choose to send message to  
one number, or to group numbers;  
2. Key in the number, then press left key to confirm, the display shows “Sending…”;  
3. When message is successfully sent, the display shows “Message sent successfully.”  
4. If sending fails, the screen will display “Send failed”;  
5. The sent message will not be saved automatically.  
To Save Message  
After you type a message, press left key, then select Save message;  
Press left key again to save this message to Outbox, the display shows “Saving…”  
To Toggle Between Upper/Lower Case, Number or Symbol  
Note: Under Phonebook/SMS mode, press # button to toggle between Upper/Lower Case,  
Number or Symbol. Press OK button to make the settings permanent.  
CONFERENCE CALLING  
You need to register with your fixed line network operator for conference calling service. It  
is dependant on service availability and subscription.  
To Make Conference Call:  
Connect the first party;  
Press RECALL button, and the first party is put on hold;  
Dial second party’s phone number;  
When connected, press RECALL button again to connect the three parties together.  
PHONEBOOK  
Up to 50 or 100 (depending on your country location) records could be stored in each  
handset's Phone Book. Each record can store up to 20 digits, and names of up to ten  
characters. In standby mode, press right key, and the display shows phonebook list.  
To Store New Number into Phonebook  
1. In standby mode, press right key, enter Phonebook mode, the display shows the  
stored numbers;  
8
 
User Manual  
2. Press left key and UP / DOWN button, and goes to the location New Entry;  
3. Then press left key again, and key in the name;  
4. Press left key to confirm, and key in the number;  
5. Now press left key to store it.  
To Delete a Number or All Numbers from Phonebook  
1. Under Phonebook, press UP / DOWN button to scroll through the stored numbers;  
2. Select the number you want to delete, then press left key, then UP / DOWN button  
till to the location Delete;  
3. Now press left key to delete current number or all numbers; the display shows Ok?  
4. Press left key to delete the number/numbers.  
To Modify (Change) a Number in Phonebook  
1. Under Phonebook, press UP / DOWN button to scroll through the stored numbers;  
2. Select the number you want to modify, then press left key, then UP / DOWN button  
to the location Edit Entry;  
3. Press left key to confirm, right key to clear the old name, and key in the new name;  
4. Press left key to save the edit, also goes to the stored number; press right key to  
clear the old number and key in the new number;  
5. Then press left key to save the change.  
CALL LOGS  
Call Logs store information related to received calls, missed calls and dialed calls. The  
phone can store up to a maximum of 30 calls, consisting of 10 received, missed and dialed  
calls respectively.  
To Check Call Records  
1. In standby mode, press left key, goes to CALL INFO (Call Information) mode;  
2. Press left key again, the display shows Missed Calls, Received Calls, Dialed calls  
and Clear All Calls;  
3. Then press left key again, the display shows these calls numbers;  
4. Select one number, press left key and UP / DOWN button to Show Details;  
5. Press left key, then the display shows the details of the call, including the call  
number, and the date and time the call is received or dialed.  
HANDSET SETTINGS  
To Set Wall Paper  
1. Select < Wall Paper> under HANDSET mode;  
2. Press left key to confirm, and press UP/DOWN button to scroll through the pictures;  
3. Choose the picture you prefer, then press left key to confirm, now the picture is set  
to the wallpaper of the handset.  
To Set External/Internal Ringer Volume (1 -5 level)  
1. Select < Ringer Set> under HANDSET mode;  
2. Press left key to confirm, then UP/DOWN button to ExternalVol /InternalVol;  
3. Press left key and UP/DOWN button to choose the volume level you want to set;  
press left key to confirm  
To Set External/Internal Ringer Melody (1-9 melody)  
1. Select < Ringer Set> under HANDSET mode;  
2. Press left key to confirm and UP/DOWN button to ExternalRing / InternalRing;  
3. Press left key and UP/DOWN button to choose the ring melody you want to set;  
press left key to confirm the choice.  
To Set Key Tone On/Off  
Each time you press a key on your handset, you hear a tone. You can turn this off if needed.  
9
 
User Manual  
1. Select < Ringer Set> under HANDSET mode;  
2. Press left key to confirm, then UP/DOWN button to Key Beep;  
3. Press left key and UP/DOWN button to set the key beep ON/OFF; press left key to  
confirm.  
Auto Talk Function  
Normally, you need to press the CALL button to answer an incoming call. But with  
AUTOTALK function turned on, when your handset is ringing for an incoming call, you can  
answer the call by simply lifting the handset from the base unit without pressing the CALL  
button.  
To Set Auto-Talk Function ON/OFF:  
1. Select <Auto-talk> under HANDSET mode;  
2. Press left key, and UP/DOWN button to set Auto-talk ON/OFF;  
3. Then press left key to confirm;  
! If you have turned Auto-talk on, do not press the CALL button after you've answered a  
call by lifting the handset, otherwise, you'll disconnect the call.  
To Set Handset Name  
1. Select <Handset Name> under HANDSET mode;  
2. Press left key to enter; Key in your chosen name; press left key again to confirm  
To Set Language  
You can change the default language into any language you prefer.  
1. Select < Language> under HANDSET mode;  
2. Press left key and UP/DOWN button to choose languages; press left key to confirm  
To Lock /Unlock the Keypad  
Press left key and “ “ button consecutively to lock/unlock the keypad.  
BASE SETTINGS  
To Set Base Melody (1-9 melody)  
1. Select < Ringer Settings> under BASE mode;  
2. Select <Ringer Melody> under Ringer Settings;  
3. Press left and UP/DOWN button to set the melody; press left key to confirm  
To Set Base Volume (1-5 volume level)  
1. Select < Ringer Settings> under BASE mode;  
2. Select <Ringer Volume> under Ringer Settings;  
3. Press left key and UP/DOWN button to set the volume; press left key to confirm  
To Set Dial Mode  
You can change dial mode to TONE or PULSE dialing.  
1. Select < Dial Settings> under BASE mode;  
2. Select <Dial Mode> under Dial Settings;  
3. Press left key and UP/DOWN button to change dial mode as TONE or PULSE; press  
left key to confirm  
Call Barring Function  
Call barring enables you to restrict or bar certain types of calls to and from your phone.  
To Set Call Barring ON/OFF  
1. Select < Call Barring> under BASE mode;  
2. Press left key and UP/DOWN button to the location Barring Mode;  
3. Press left key and UP/DOWN button to set Call barring ON/OFF; press left key to  
confirm.  
10  
 
User Manual  
To Set Call Barring Number  
1. Select < Call Barring> under BASE mode;  
2. Select <Barring Number> under Call Barring;  
3. Press left key, then key in the PIN (the default PIN is 0000);  
The display shows one of the numbers from 1 to 5 (the maximum call barring  
numbers you can set), and then key in the telephone number you want to set call  
barring.  
4. Press left key, and then the display shows HS?  
Key in the handset number that you want to set call barring  
5. Press left key to confirm.  
To Delete Call Barring Number  
1. See 1-3 step above, press left key; the display show the call barring number you set  
2. Press and hold right key to clear the number; press left key to confirm.  
To set Auto Pause  
With the Auto Pause function, the phone will automatically pause for 3 seconds once the  
initial string of the phone number matches the PABX code. For example, if the user  
program to enter "9" as PABX code, then when he dials "98118118", then the phone will dial  
“9” first then pause for 3 seconds follow by “8118118”. To set Auto Pause:  
1. Select < Dial Settings> under BASE mode;  
2. Select <Auto Pause > under Dial Settings;  
3. It will prompt for pin, key in the pin (the default PIN is 0000)  
4. Key in the PABX number. Maximum 5 numbers can be entered. Press left key to  
confirm.  
To set Flash  
With the FLASH function, you may select Short or Long flash time for your PABX. You may  
activate FLASH by pressing R button. To set FLASH:  
1. Select < Dial Settings> under BASE mode;  
2. Select <Flash Time> under Dial Settings;  
3. It will prompt for Short or Long flash. Select either one and press left key to  
confirm.  
To Change Base PIN  
1. Select <PIN> under BASE mode;  
2. Press left key, and key in the original PIN (default PIN:0000) number;  
3. Then press left key to confirm, and key in New PIN;  
4. Press left key, then key in New PIN again; press left key to confirm  
EXTRA SETTINGS  
To Set Alarm Time  
1. Select < Alarm Set > under EXTRA mode;  
2. Press left key, then key in the time; press left key to save;  
To Set Clock Time  
1. Select < Clock Set > under EXTRA mode;  
2. Press left key, then key in the time; press left key to save;  
To Set Clock Date  
1. Select < Clock Date > under EXTRA mode;  
2. Press left key, then key in the date;  
3. Press left key to save;  
11  
 
User Manual  
RESETTING THE SYSTEM  
If you have set a PIN and forgotten it, you need to reset the system. The PIN will be reset  
to 0000. If you reset the system, you will lose all stored information (including numbers in  
memory) and all features will return to their default settings.  
While you are resetting the system, you should disconnect the telephone line cord from the  
back of the base unit, so you won't be interrupted by incoming calls. To reset the system  
without the PIN:  
1. Disconnect the power lead from the back of the base unit;  
2. Press and hold the HANDSET LOCATOR PAGE button in the base unit;  
3. Connect the power lead into the back of the base unit. After you hear "beep" sound  
for five times, then release the LOCATOR button  
4. You will hear confirmation tone from the base unit.  
HANDSET REGISTRATION  
Your phone is supplied with the handset already registered to the base unit, and you  
shouldn't need to register it. But if you've bought extra handset, you'll need to register each  
one to your original base unit. Maximum 5 handsets can be registered to one base.  
To register a handset  
1. Press and hold the Handset locator PAGE button on the base unit for a while, until  
you hear "beep" sound twice continuously;  
2. Press left key, then UP/DOWN button to the location REGISTRATION;  
3. Press left key, then UP/DOWN button to the location BASE SUB;  
4. Press left key again, The display shows BASE 1; BASE 2; BASE 3; BASE 4;  
5. Press UP/DOWN button to scroll through base, and press left key, then enter base  
PIN, and press left key to confirm, the display shows SEARCH + selected number  
After a while, when the handset finds the base unit, the display shows PIN  
INTERCOM AND TRANSFER  
To make an intercom call  
1. Press the RECALL button and you hear the DIAL Tone  
2. Key in the number of the other handset  
On the other handset's display, your number appears, and the INT symbol flashes. Then the  
other handset user presses the CALL button to connect the call.  
For details of how to change the ringing melody and volume for intercom calls, see "INT  
MELODY" and "INT VOLUME" under "HANDSET SETTING" part.  
To end an intercom call  
Press the CALL button on your handset. The other person will hear Busy  
tone, and also need to press the CALL button to hand up.  
To transfer a call  
When you have made or answered an outside call, to transfer it to another handset:  
Press the RECALL button and key in the number of the other handset;  
Press the CALL button to hang up and transfer the call  
The outside call is put on hold. When the other handset answers, you can speak to the user.  
If the other handset does not answer, you can get back to the outside call by pressing the  
RECALL button again.  
12  
 
User Manual  
TROUBLESHOOTING  
If you experience difficulties with the operation of your phone, refer to the advice given  
below.  
1. "The handset does not ring"  
Check the base unit's mains power adaptor is plugged in and power is switched on. The base  
unit needs mains power for normal operation of the phone, not just for charging the  
batteries.  
Make sure you are using the telephone line cable that was supplied with your  
phone. Other telephone line cables might not work.  
2. "There is no dial tone"  
Check that the handset is registered to the base station.  
Check that the line cord is securely connected at both ends and is undamaged.  
Check the power to the base station is on and connected.  
3. "The base does not ring."  
Check that the base power is ON, and the base ringer is set ON.  
Check that the line cord is correctly fitted and undamaged.  
4. "The CHARGE light on the base unit does not come on."  
Check the handset is properly stationed.  
Check the connections between the base unit and mains power socket.  
Clean the battery charging contacts with a dry cloth.  
5. "When I press the CALL button, I hear a loud noise."  
The strange noise is caused by interference. Disconnect the mains power lead from the  
back of the base unit, and then wait for 30 seconds before reconnecting it.  
7. "I cannot make or answer calls."  
Move the handset closer to the base unit.  
Try a different location for the base unit, perhaps higher, or further from other electrical  
equipment.  
Check the Battery Level symbol on the display. If it is low, replace the handset on the base  
unit to recharge the batteries.  
Switch off power at the mains socket, wait for a few seconds and then switch back on.  
8. "The handset’s battery are running low within an hour or two."  
Before you used the handset for the first time, you should have left it on the base unit for  
up to 15 hours to charge the battery fully.  
You may need to replace the battery.  
9. "Last Number Redial and/or memory dialing don't work on a PBX."  
When you first make a call, try press the # button for a pause between the outside line  
access digit and the telephone number.  
You should later be able to redial the number.  
10. "I cannot transfer a call."  
Make sure the other handset is within range of the base unit, and is not busy on a call.  
Make sure you are keying in the correct number for the other handset.  
13  
 
User Manual  
TECHNICAL DETAILS  
Full DECT GAP Compatible System  
Standard  
Frequency range  
: 1.88 to 1.9 GHz  
Channel bandwidth  
Modulation  
: 1.728 MHz  
: GMSK  
Operating range  
: Up to 300 m outdoor. Up to 50 m indoor  
Operating time  
: Standby time of 100 hours, Operating time of 8 hours.  
: Operating at 00C to 400C, Storage at 200C to 600C  
Temperature range  
Electrical power  
: Handset- 2x1.2V 750mAH NiMH rechargeable battery  
Base- Input 230 V AC, 50 Hz. Output AC 9 V, 300mA  
PABX compatibility  
: Pause length: 3 seconds. Signaling type: DTMF (dual-tone  
multifrequency) Pulse dialing.  
DECLARATION OF CONFORMITY  
The SD8301 complies with the essential protective requirements and objectives of:  
EC R& TTE Directive 1999/5/EC  
EC Low Voltage Directive 73/23/EEC  
EC EMC Directive 89/336/EEC  
14  
 

Sennheiser Microphone 500203 User Manual
Sharp Microwave Oven R 890N User Manual
Shindaiwa Trimmer 82053 User Manual
Shure Headphones bg41 User Manual
Snapper Lawn Mower ZU2014K User Manual
Sony CD Player CDX 646X User Manual
Sony Speaker System SMS 2P User Manual
Subaru Robin Power Products Portable Generator 505D User Manual
Sylvania Flat Panel Television LD200SL9 User Manual
Tanaka Edger TPE 270PN User Manual