Shiro Cordless Telephone SD3101 User Manual

User Manual •  
SD3101  
Digital Enhanced Cordless Communication  
 
What the symbols mean  
Batteries charge level  
Whenever this shows ‘nearly empty’ (  
), put the handset on the base unit to charge the  
batteries. While the batteries are being charged, the level shown will keep changing.  
Outside call  
You are connected to an outside call.  
Intercom call  
You are connected to an intercom call.  
Phone book  
Show the names and numbers of stored record.  
Mute  
Your handset's microphone is muted.  
Up and down arrows  
To browse through the programming menu for more options.  
Speakerphone  
Your handset’s loudspeaker is on.  
Signal level  
Shows the strength of the signal between the handset and base unit, and flashes when you are  
out of range of the base unit, when the level is low, or the symbol is flashing, move closer to  
base unit.  
Missed call  
You have new missed call.  
2
 
 
The Handset and Base Unit  
MENU/ Mute button  
PHONEBOOK/OK/Recall button  
Press to enter menu mode  
and enter sub-menu. Use  
the key " " to lock or  
unlock the keypad.  
Press during a call to mute  
the microphone  
In standby mode, press to enter  
phonebook mode.  
Press to confirm selection.  
You can activate Recall function if  
your phone is connected to a PABX,  
or if you use Select Services.  
Press to transfer an outside call to  
another phone.  
INT button  
Speakerphone button  
Press to turn the  
speakerphone ON/OFF  
Press to make an intercom call (if you  
have more than one handset)  
Clear / On-Off /End button  
Call button  
Press and hold (2-3 seconds) to switch  
the handset on and off. Press during  
programming to go back to the  
previous option, or to clear digits one  
by one from the display.  
Press to begin and  
answer the call  
Press to end the call.  
UP/DOWN button  
In standby mode, press  
to show phonebook list;  
Press during  
programming to move  
through the menu. Press  
during a call to change  
the volume in the  
IN USE light  
The IN USE light comes on when you  
have a connection to the telephone line.  
HANDSET LOCATOR button  
earpiece.  
Press this to make the handset ring,  
if you cannot remember where you put it.  
Press it again to stop the handset ringing.  
Before you can use the handset to make  
calls for the first time, you will need to  
fit and fully charge the battery for 15  
hours.  
3
 
 
Setting up your telephone  
Connection and conditions for use  
You can connect your SD3101 to a direct exchange line (DEL), a line connected to a local  
exchange, with its own phone number; to an extension socket connected to a DEL; or to an  
extension on an approved compatible PBX. Do not connect the SD3101 as an extension to a  
payphone.  
How many phones can you connect?  
The ringer equivalence numbers (RENs) of all instruments (phones, fax machines, etc.)  
connected to an exchange line must not add up to more than 4, otherwise, one or more of  
them may not ring and/or answer calls correctly. The SD3101 has a REN of 1, and most  
other telephones have a REN of 1 unless marked otherwise.  
Radio signals between handset and base unit  
To use your handset and base unit together, you must be able to establish a radio link  
between them. Be aware that:  
Sitting the base unit as high as possible will give better results, in a two-storey house,  
the best position may be on the first-floor landing.  
Any large metal object, like a fridge, a mirror or a filing cabinet, between the handset  
and base unit may block the radio signal.  
Other solid structures, like walls, may reduce the signal strength.  
Choosing a site for the base unit  
The base unit should be placed on a level surface, in a position where:  
The mains adapter plug will reach a 230-V AC switched mains supply socket; never  
try to lengthen the mains power cable.  
The telephone cable will reach your telephone line socket or extension socket.  
It is not close to another telephone, this can cause radio interference.  
It is not close to a sink, bath or shower, or anywhere else where it might get wet.  
It is not close to other electrical equipment, fridges, washing machines, microwave  
ovens, TVs, fluorescent lights, etc.  
What's in this pack  
Please check the box contents for completeness.  
If any parts are missing, return complete box to your supplier.  
The cordless handset  
The base unit  
Rechargeable AAA batteries  
A telephone line cable (different from country to country)  
A mains power lead and adaptor (different from country  
to country)  
Charger pods (not available for single handset)  
User manual  
Note: Keep your proof of purchase to support any  
Guarantee claim  
4
 
 
Installation  
1. Choose a suitable site for the handset unit  
Make sure it is not near to another telephone, nor to other electrical equipment.  
2. Plug the mains power lead into the power jack on the base unit and plug the  
telephone line cord into the telephone port.  
3. Plug the mains adapter into a 230V AC, 50 Hz mains socket, with the switch on  
the socket set to OFF  
Note: The illustration of adaptor may vary from country to country.  
4. Switch on mains power at the socket  
5. Fit the battery in the handset(s)  
Insert the battery pack as shown. Fit the battery compartment cover,  
Sliding it until it clicks firmly into position.  
6. Connect the base unit to the telephone line  
5
 
 
Important safety information  
This equipment is not designed for making emergency calls in the event of a power failure.  
Alternative arrangements should be made for access to emergency services.  
(This means that you should also have a basic phone that does not need mains power,  
connected to your line so that you can make calls during a power failure)  
People with a heart pacemaker should consult their doctor before using the telephone.  
If you wear a hearing aid, you should note SD3101 works by transmitting radio waves  
between base and handset that may cause a humming noise.  
1. DO NOT clean any part of your phone with benzene, thinner or other solvent chemicals,  
which may cause permanent damage to your phone. This damage is not covered by the  
Guarantee. When necessary, clean it with a damp cloth.  
Cleaning it with a wet cloth may give you an electric shock.  
2. DO NOT use this equipment in places where volatile or explosive materials may be  
present.  
3. DO NOT let the base unit get wet. Electrical equipment can cause serious injury if used  
while you are wet or standing in water. NEVER use your phone during a thunderstorm.  
Unplug the base unit from the telephone line and the mains socket when there are storms in  
your area. Damage caused by lightning is not covered by the Guarantee.  
4. The SD3101 will produce a certain amount of heat during operation. For this reason it is  
recommended that this equipment is NOT placed in direct contact with antique, veneered or  
delicate furniture surfaces.  
5. DO NOT dispose batteries with normal household waste.  
6. The SD3101 DECT phone emits radio signals which could interfere with other electronic  
equipment, computers, radio, TV set, clock radio alarms, etc.  
A distance of at least one meter should be maintained between SD3101 base station and other  
equipment. This will minimize the risk of such interference.  
7. When you do not need to carry your handsets around, leave them on the base unit or  
charger pod, to keep the batteries charged.  
8. If you hear a warning tone as move around during a call, and/ or the sound in the earpiece  
becomes faint or distorted; you may be going out of range of the base unit.  
Move nearer to the base unit within 20 seconds, until the tone stops. Otherwise your call may  
be cut off.  
! NOTE: Dispose of used batteries safely, never burn them, or put them where they could  
get punctured.  
6
 
 
Making and answering calls  
To switch the handset ON or OFF  
Press and hold the CLEAR button for 2~3 seconds to switch the handset ON /OFF.  
To make a call  
1. Key in the telephone number (If you make a mistake, press CLEAR button to clear  
digits from the display. To clear all digits, press and hold CLEAR button.)  
2. Press the CALL button.  
3. Or you also can dial the stored number through UP/DOWN button.  
Note: You can dial the number after you press the CALL button if you need, but you won't  
be able to correct any mistakes if you do it in this way.  
When you dial the outside line access digit (e.g. 9) then the telephone number, press and hold  
the "#" button about 2 seconds for a pause.  
To redial a call  
In standby mode, press and hold the CALL button to enter the dial list, and press the  
UP/DOWN button to scroll through the number you want to dial, then press the CALL  
button to redial.  
To answer a call  
When the handset and base unit ring, press the CALL button to answer a call, and the  
symbol  
or  
appears in the display.  
When the AUTO TALK is turned on, you can simply answer the call by lifting the handset  
from the base unit (see AUTO TALK part).  
To end a call  
Press the END button to end a call.  
Earpiece volume  
During a call, to adjust the volume of the earpiece:  
Press the UP or DOWN button to change the volume.  
Muting the mouthpiece  
During a call, if you want the person on the other hand end cannot hear you; press  
MUTE once to mute the mouthpiece;  
While the mouthpiece is muted, you cannot press any number key to send digits down  
the line; Press MUTE key again to get back to the call.  
Conference Calling  
You need to register with your fixed line network operator for conference calling service. It  
is dependant on service availability and subscription.  
To Make Conference Call:  
1. Connect the first party;  
2. Press INT button, and the first party is put on hold;  
7
 
 
3. Dial second party’s phone number;  
4. When connected, press and hold “#” button to connect the three parties together.  
Phone Book  
Up to 30 records could be stored in each handset's Phone Book. Each record can store up to  
20 digits, and names of up to 8 characters could be stored with the number. In standby mode,  
press UP/DOWN button to show phonebook list. There are two ways to enter phonebook.  
In standby mode, press PHONEBOOK button to enter phonebook; or through MENU and  
UP/DOWN button to enter phonebook.  
To store new number into phonebook  
1. Press the OK button, the display shows ADD  
2. Press the OK button again, then key in the name and the number  
3. Press the OK button to confirm  
4. Press the CLEAR button twice to return to standby mode, or you can continue to  
store number.  
To clear a number from phonebook  
1. Press the OK button, the display shows ADD  
2. Press UP/DOWN button to the location DELETE  
3. Press OK button to confirm, then press UP/DOWN button to select the number you  
want to delete  
4. Press the OK to delete the name and number, the display shows DELETE  
5. Press the CLEAR button to return to standby mode  
To modify (change) a number in phonebook  
1. Press the OK button, the display shows ADD  
2. Press UP/DOWN button to the location EDIT, then press OK to confirm, the display  
shows the first stored number  
3. Press UP/DOWN button to select the number you want to modify, then press OK to  
confirm  
4. Press CLEAR button to clear the old name, then key in the new name;  
5. Press OK to save the edit, press CLEAR button to clear the old number and key in  
the new number.  
6. Press OK to save the change, then Press the CLEAR button to return to standby  
mode  
To clear all numbers from phonebook  
1. Press the OK button, the display shows ADD  
2. Press UP/DOWN button to the location DEL ALL  
3. Press the OK button to delete all numbers, the display shows OK?  
4. Press the OK button to confirm, the display shows EMPTY.  
To dial a number from phonebook  
1. In standby mode, press UP/DOWN button to enter the phonebook list directly;  
2. Key in the first letter of the name to quick search the accordance number you want to  
Dial;  
3. Press CALL button.  
8
 
 
Call Logs  
You must subscribe to Caller ID service from your service provider to use this feature.  
Call Logs store information related to received calls, missed calls and dialed calls. The  
SD3101 can store up to a maximum of 30 calls, consisting of 10 received, missed and dialed  
calls respectively.  
To check call records  
1. Press the MENU button  
The display shows CALL LOGS  
2. Press the OK button, then press UP/DOWN button to the locations MISSED,  
RECEIVED, or DIALED calls.  
3. Press the OK button, then press UP/DOWN button to scroll the records  
To save a number in call logs  
When you received a new number, you want to store in phonebook. The following is for your  
reference.  
1. Repeat step 1 to 3 above, until the display shows the new number.  
2. Press the MENU button, the displays shows SAVE  
3. Press the MENU button, the displays shows NAME?  
4. Key in the name, Press the MENU button to save.  
To edit a number in call logs  
1. Repeat step 1 to 3 in “To check call records” section, until the display shows the  
number;  
2. Press the MENU button, then press UP/DOWN button to the location EDIT;  
3. Press the OK button, then press CLEAR button to clear the old number and key in  
the new number;  
4. Press the OK button to save the change.  
To clear a number in call logs  
1. Repeat step 1 to 3 in “ To check call records” section, until the display shows the  
number;  
2. Press the MENU button, then press UP/DOWN button to the location DELETE;  
3. Press the OK button to confirm.  
To clear all number in call logs  
1. Repeat step 1 to 3 in “To check call records” section, until the display shows the  
number;  
2. Press the MENU button, then press UP/DOWN button to the location DEL ALL;  
3. Press the OK button, the display shows OK?  
4. Press the OK button to confirm.  
To dial a number from call logs  
1. Ensure the required name/number is visible on the display  
2. Press CALL button  
9
 
 
Handset Setting  
Key tone on and off  
Each time you press a key on your handset, you hear a tone. You can turn this off if needed.  
1. Press the MENU button, then press UP/DOWN button to the location HANDSET  
2. Press the OK button  
The display shows KEYTONE  
3. Press the OK, the display shows ON? or OFF?  
4. Press the OK button to confirm  
Ringer Volume (EXT / INT)  
You can adjust the ringer volume following the below instruction.  
1. Press the MENU button, then press UP/DOWN button to the location HANDSET  
2. Press the OK button, then press UP/DOWN button to the location EXT VOL / INT  
VOL  
3. Press the OK button  
The display shows the current volume level  
4. Press UP/DOWN button to change the volume  
5. Press the OK button to confirm the volume level you want  
Ringer Melody (EXT / INT)  
You can choose the ringer Melody following the below instruction.  
1. Press the MENU button, then press UP/DOWN button to the location HANDSET  
2. Press the OK button, then press UP/DOWN button to the location EXT RING / INT  
RING  
3. Press the OK button  
The display shows the current melody  
4. Press UP/DOWN button to change the melody  
5. Press the OK button to confirm the melody you want  
Display language  
You can select the language from the menu up to your preference:  
1. Press the MENU button then press UP/DOWN button to the location HANDSET  
2. Press the OK button then press UP/DOWN button again to the location LANGUAGE  
3. Press the OK button  
The display shows the current language  
4. Press UP/DOWN button to the language you prefer  
5. Press the OK button to confirm  
Your handset name  
1. Press the MENU button, then press UP/DOWN button to the location HANDSET  
2. Press the OK button, then press UP/DOWN button to the location SET NAME  
3. Press the OK button  
The display shows the current name  
4. Press the CLEAR button repeatedly to clear the display, then key in your chosen  
name  
5. Press the OK button to confirm  
10  
 
 
Auto Talk  
Normally, you need to press the CALL button to answer an incoming call. But with  
AUTOTALK turned on, when your handset is resting on the base unit and it rings for an  
incoming call, you can answer the call by simply lifting the handset. To turn auto-talk  
ON/OFF:  
1. Press the MENU button then UP/DOWN button to HANDSET  
2. Press the OK button then UP/DOWN button to AUTOTALK  
3. Press the OK button again, the display shows ON? / OFF?  
4. Press the OK button to confirm  
! If you have turned auto-talk on, do not press the CALL button after you have answered a  
call by lifting the handset, otherwise, you'll disconnect the call.  
To Lock /Unlock the keypad  
Press MENU button and “ “ button consecutively to lock or unlock the keypad.  
Base Setting  
Note: The default PIN is: 0000  
Call Barring Function (Optional)  
Call barring enables you to restrict or bar certain types of calls from your phone.  
To set call barring number  
1. Press MENU button then UP/DOWN button until the display shows BASE SET  
2. Press the OK button, the display shows PIN?  
3. Key in your PIN number and press the OK button, then press UP/DOWN button to  
the location BARRING  
4. Press the OK button, then UP/DOWN button. The display shows one of the numbers  
from 1 to 5 (The maximum call barring numbers you can set), and then key in the  
telephone number you want to set call barring  
5. Press OK button, then the display shows HS?  
Key in the handset number that you want to set call barring  
6. Press OK button to confirm  
To delete call barring number  
1. Press MENU button then UP/DOWN button until the display shows BASE SET  
2. Press the OK button, the display shows PIN?  
3. Key in your PIN number  
4. Press the OK button, then UP/DOWN button to the location BARRING  
5. Press the OK button, the display shows the call barring number you set.  
6. Press the CLEAR button to delete the number  
7. Press OK button to confirm  
Base Melody  
You can adjust the Base Melody following the below instruction.  
1. Press MENU button then UP/DOWN button to the location BASE SET  
2. Press OK button and Key in the PIN number  
11  
 
 
3. Press OK button then UP/DOWN button to the location B Melody  
4. Press OK button and press UP/DOWN button to change the melody  
5. Press the OK button to confirm the melody you chosen  
Base Volume  
You can adjust the base volume following the below instruction.  
1. Press MENU button then UP/DOWN button to the location BASESET  
2. Press OK button and Key in the PIN number  
3. Press OK button then UP/DOWN button to the location B VOLUME  
The display shows the current volume level  
4. Press UP/DOWN button to change the volume  
5. Press the OK button to confirm the volume level you chosen  
Least cost route (LCR) function (Optional)  
With the LCR function, the phone will automatically replace a long number (up to 11 digits)  
with a comparative short number (up to 3 digits), to simplify the process of dialing a long  
number.  
Example:  
If you program to replace "00" with "17909", whenever you dial a number beginning with  
the“00”, the phone will automatically change this to “17909”. If he dials "00 15151500", the  
phone will automatically replace the number to be dialed out as “17909 15151500”  
Note:  
LCR function only replace the prefix of the phone number you dial.  
To set LCR:  
1. Press MENU button then UP/DOWN button to the location BASE SET  
2. Press the OK button, the display shows PIN?  
3. Key in your PIN number and press the OK button, then UP/DOWN button to the  
location LCR  
4. Press the OK button, the display shows SHORT?  
5. Press the OK button, the display shows EMPTY, key in the short number you want to  
replace the long number directly  
6. Press the OK button to confirm, then the display shows LONG?  
7. Press the OK button, the display shows EMPTY, key in the long number  
8. Press the OK button to confirm  
To Set Dial Mode  
You can change dial mode to TONE or PULSE dialing.  
To set dial mode:  
1. Press MENU button, then UP/DOWN button to the location BASE SET  
2. Press the OK button, the display shows PIN?  
3. Key in your PIN number and press the OK button, then press UP/DOWN button to  
the location DIAL MODE  
4. Press the OK button and press UP/DOWN button to change Dial mode as TONE or  
PULSE dialing  
12  
 
To reset base  
1. Press MENU button, then UP/DOWN button to the location BASE SET  
2. Press the OK button, the display shows PIN?  
3. Key in your PIN number and press the OK button, then UP/DOWN button to the  
location B RESET  
4. Press OK button, then the display shows RESET?  
5. Press OK button to confirm, or Press CLEAR button, and go back to B RESET  
To change base PIN  
1. Press MENU button, then UP/DOWN button to the location BASE SET  
2. Press the OK button, the display shows PIN?  
3. Key in your PIN number and press the OK button, then UP/DOWN button to the  
location MAST PIN?  
4. Press OK button, the display shows PIN?, Key in the original PIN number(default  
PIN:0000)  
5. Repeat the step 4 and the display shows MAST PIN  
6. Press OK button, the display shows PIN?, Key in the new PIN number,  
7. Repeat the step 6, and press OK button to confirm  
PABX  
With the PABX function, the phone will automatically pause once the initial string of the  
phone number matches the PABX code. For example, if the user program to enter “9” as  
PABX code, then when he dials “98118118”, then the phone will dial “9” first then pause  
follow by “8118118”.  
To set PABX number:  
1. Press MENU button, then press UP/DOWN button to the location BASE SET;  
2. Press the OK button, the display shows PIN?;  
3. Key in your PIN number and press the OK button, then UP/DOWN button to the  
location PABX?;  
4. Press the OK button, the display shows PABX 1?. You may press UP/DOWN button  
to select PABX 2  
5. Press the OK button, the display shows EMPTY. Key in the code. The maximum  
PABX code length is 5 digits.  
6. Press OK button to confirm.  
FLASH  
With the FLASH function, you may select Short or Long flash time for your PABX. To set  
FLASH:  
To set flash time:  
1. Press MENU button, then press UP/DOWN button to the location BASE SET;  
2. Press the OK button, the display shows PIN? ;  
3. Key in your PIN number and press the OK button, then UP/DOWN button to the  
location FLASH?;  
4. Press the OK button, the display shows SHORT? . You may press UP/DOWN button  
to select LONG?  
5. Press the OK button to confirm.  
13  
 
Resetting the system  
If you have set a PIN and forgotten it, you need to reset the system. The PIN will be reset to  
0000. If you reset the system, you will lose all stored information (including numbers in  
memory) and all features will return to their default settings. You need to register the handset  
to the base unit again.  
While you are resetting the system, you should disconnect the telephone line cord from the  
back of the base unit, so you won't be interrupted by incoming calls. To reset the system  
without the PIN:  
1. Disconnect the power lead from the back of the base unit  
2. Press and hold the HANDSET LOCATOR button in the base unit, at the same time  
connect the power lead into the back of base unit. Release the LOCATOR button  
after you hear “beep” sound for five times. The IN USE light on base unit lights  
during this whole process.  
3. After 2~3 seconds, you can hear “beep” sound for two times again and the IN USE  
light goes off;  
4. Disconnect the power lead from base, and then connect it again, you will hear  
confirmation tone from the base unit.  
Handset registration  
Your SD3101 is supplied with the handset already registered to the base unit, and you  
shouldn't need to register it. But if you've bought extra handsets separately, you'll need to  
register each one to your original base unit. Maximum 4 handsets can be registered to one  
base.  
To register a handset  
1. Press and hold the Handset locator button on the base unit for a while, until you hear  
"beep" sound twice continuously.  
2. Press the MENU button, then press UP/DOWN button to the location REGISTER  
3. Press the OK button, then press UP/DOWN button to the location SUB BASE  
4. Press the OK button again  
The display shows BASE? 1 2 3 4  
5. Key in a base unit number  
The display shows SEARCH + selected number, then shows the ID of the base unit  
after 3~4 seconds.  
6. Press the OK button again  
The display shows PIN?  
7. Key in your pin (default 0000) and press OK to confirm.  
If the display says NOT REG, check to see if you key in the correct PIN, then  
repeat the registration procedure again from step 1.  
14  
 
 
Intercom and transfer  
To make an intercom call  
1. Press the INT button  
2. Key in the number of the other handset  
On the other handset's display, your number appears, and the INT symbol flashes. Then the  
other handset user presses the CALL button to connect the call.  
For details of how to change the ringing melody and volume for intercom calls, see "INT  
MELODY" and "INT VOLUME" on "HANDSET SETTING" part.  
To end an intercom call  
Press the CALL button on your handset  
The other person will hear Busy tone, and should also press the CALL button to hand up.  
To transfer the outside call to another handset (if you have two or more handsets):  
Press the INT button and key in the number of the other handset.  
The outside call is put on hold. When the other handset answers, you can speak to the  
user. If the other handset does not answer, you can get back to the outside call by  
pressing the INT button again.  
To transfer the outside call to another outside phone:  
Press the Recall button and key in the call number you want to transfer.  
The first party is put on hold. When second party answers, you can speak to the user,  
then press the CALL button to hang up and transfer the call.  
Note: Network Depending  
Troubleshooting  
Always check first that:  
You have followed the steps listed on pages to install and set up your SD3101.  
All connects are firmly inserted in their sockets.  
Mains power is switched on at the socket.  
The handset’s batteries are correctly and securely installed, and are not run down.  
If you experience difficulties with the working of your SD3101, refer to the advice given  
below.  
I cannot make or answer calls.  
Check that the base unit’s mains power adapter is plugged in and power is switched on. The  
base unit needs mains power for normal operation of the phone-not just charging the batteries.  
Make sure you are using the telephone line cable that was supplied with your SD3101. Other  
telephone line cables might not work.  
Move the handset closer to the base unit.  
15  
 
 
Check the batteries level symbol on the display. If it is low, replace the handset on the base  
unit or charger pod to recharge the batteries.  
Switch off power at the mains socket, wait for a few seconds and then switch back on. This  
may solve the problem.  
If you still can’t make calls, try re-registering the handset.  
When I press keys on the handset, nothing happens.  
Make sure the batteries are fitted in your handset. If the batteries level symbol on the display  
shows “low”, recharge the batteries.  
Check whether there’s a key symbol on the display. If so, the keypad is locked. Turn to the  
user manual to find out how to unlock it.  
When I press keys on the handset, digits appear on the display, but I can’t make an  
outside call.  
Call barring may have been set, see the user manual for more information.  
Try moving the handset closer to the base unit.  
Try a different position for the base unit-perhaps higher, or further from other electrical  
equipment.  
The phone does not ring  
Check that the base unit’s mains power adapter is plugged in and power is switched on. The  
base unit needs mains power for normal operation of the phone-not just charging the batteries.  
Make sure you are using the telephone line cable that was supplied with your SD3101. Other  
telephone line cables might not work.  
Check that you have set the ringer volume to off. See the user manual for more information.  
Check that the total REN value of all equipment connected to your telephone line is no more  
than 4. Disconnect one or more telephones and see whether that helps.  
The base does not ring.  
Check that the base power is ON, and the base ringer is set ON.  
Check that the line cord is correctly fitted and undamaged.  
The CHARGE light on the base unit does not come on."  
Check the handset is properly stationed.  
Check the connections between the base unit and mains power socket.  
Clean the batteries charging contacts with a dry cloth.  
When I press the CALL button, I hear a loud noise.  
16  
 
The strange noise is caused by interference. Disconnect the mains power lead from the back  
of the base unit, and then wait for 30 seconds before reconnecting it.  
There is 'beep' sound while I am on a call.  
You may be going out of range of the base unit. Move closer, or your call may be cut off.  
Check the Batteries Level symbol on the display. If it is low, recharge the batteries.  
The Caller Display feature isn’t working.  
You need to subscribe to the Caller Display feature from your service provider.  
The caller may have withheld their number, or they may be calling from a network that does  
not transmit the Caller ID (for example, it may be an international call).  
The handset’s battery is running low within an hour or two.  
Before you used the handset for the first time, you should have left it on the base unit for up  
to 15 hours to charge the batteries fully.  
You may need to replace the batteries.  
I cannot transfer a call.  
Make sure the other handset is within range of the base unit, and is not busy on a call.  
Make sure you are keying in the correct number for the other handset.  
No display on LCD screen.  
Make sure the batteries have power.  
I cannot register handset to base  
Make sure the number of handset registered to base is less than 4.  
Check that the base unit is not near other electrical equipment, such as TV or computer  
Technical details  
Full DECT GAP Compatible system  
Standard  
:
:
:
:
:
:
:
:
Digital Enhanced Cordless Telecommunications (DECT)  
1.88 to 1.9 GHz  
1.728 MHz  
Frequency range  
Channel bandwidth  
Modulation  
Operating range  
Operating time  
Temperature range  
Electrical power  
GMSK  
Up to 300 m outdoors; Up to 50 m indoors  
Standby time: 90 hours ; Talking time: 8 hours  
Operating 00C to 400C; Storage -200C to 600C  
Handset--- two 1.2V 550mAH NiMH rechargeable Batteries  
Base unit---input 230 V AC, 50 Hz; Output AC 7.5V, 350 mA.  
17  
 
 
Declaration of conformity  
The SD3101 complies with the essential protective requirements and objectives of:  
EC R& TTE Directive 1999/5/EC  
EC Low Voltage Directive 73/23/EEC  
EC EMC Directive 89/336/EEC  
18  
 
 

SIIG Network Card 485 PCI User Manual
Singer Sewing Machine 138K1 User Manual
Snapper CRT Television EZT18542150ZBVE 2690612 User Manual
Sony Corded Headset DRGA100 VLT User Manual
Sony Ericsson Speaker System NAS C5E User Manual
Sony Stereo System CDP XA20ES User Manual
Sony Tablet 20 SVJ202 User Manual
Sony TV Receiver DHG M55CV User Manual
Superior Indoor Fireplace VFPF CMN 2 User Manual
Sylvania Portable DVD Player SDVD9000 User Manual